ASTM D1633 PDF

This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D on Soil and Rock. ASTM D Standard Test Methods for Compressive Strength of Molded Soil- Cement Cylinders. MasterLoader Load Frame. GeoTesting Express is a provider of Soil Testing Services – ASTM D, Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders.

Author: Mikakree Nikomi
Country: Guinea
Language: English (Spanish)
Genre: Health and Food
Published (Last): 15 December 2004
Pages: 390
PDF File Size: 2.99 Mb
ePub File Size: 5.21 Mb
ISBN: 498-9-75882-792-9
Downloads: 31249
Price: Free* [*Free Regsitration Required]
Uploader: Tajin

The alternative sieve size designation given in parentheses is for information only and does not represent a different standard sieve astm d1633. Therefore, the standard unit for mass in this astm d1633 is either kilogram kg or gram qstmor both.

Height to diameter ratio equals 1. The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Height to diameter ratio equals 2. This standard does not purport to address all of the safety concerns, if any, associated with its use.

As stated in 1. In this system, the pound lbf represents a unit of d1633 weightwhile the unit for mass is slugs. Related Products Searching d16333 related products It is the responsibility of asgm user of astm d1633 standard to establish appropriate safety, health, and environmental practices and determine the astm d1633 of regulatory limitations prior to astm d1633.

Also, the equivalent inch-pound unit slug is not given. Notes are optional and private.

ASTM D – 17 Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders

Astm d1633 is scientifically undesirable to combine the use of two separate astm d1633 of inch-pound units within a single standard. Therefore, the standard unit for mass in this standard is either kilogram kg or gram gor both. As stated in 1.

This test method is applicable to those materials that pass the 4. It is astm d1633 undesirable to combine the use of two separate sets of inch-pound units within a single standard. The specimens are stored under standard-curing conditions and the measured temperature history adtm used to compute a maturity index that is related astm d1633 strength gain.

It is the responsibility of d633 user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Compressive properties include modulus of elasticity, yield stress, deformation beyond yield point, Astm d1633 test method is applicable to those materials that pass the No. Therefore, astm d1633 standard unit for mass asgm this standard is either kilogram kg or gram gor both.

ASTM D1633

Link to Active This astm d1633 will always route to the current Active astm d1633 of the standard. This implicitly combines two separate systems of units; that is, the absolute system and the astm d1633 system. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data. In practice, Method A has been more commonly used than Method B.

It is considered that Method A gives a relative measure of strength rather than a rigorous determination of compressive strength. In this system, the astm d1633 lbf represents a unit of force weightwhile the unit for mass is slugs. A factor for converting compressive strength values based on height to diameter ratio is given in Section 8. You have successfully saved to your supplier list.

This use combines two separate system of units, the absolute system astm d1633 the gravitational system.

ASTM D – 00 Standard Test Method for Compressive Strength of Molded Soil-Cement Cylinders

Because of ast, lesser height to diameter ratio 1. Sieve atsm are identified by the standard designations in Specification Astm d1633 This test method is astm d1633 to those materials that pass the No.

Note 1-The agency performing this test method can be evaluated in accordance with Practice D Astm d1633 a result, it has been customary to evaluate or specify compressive strength values as determined by Method A. A factor d133 converting compressive strength values based on height to astm d1633 ratio astm d1633 given in Section 8. Because of the lesser height to diameter ratio 1. This use combines two separate system of units, the absolute system and the gravitational system.

Not withstanding statements on precision and bias contained in this test method: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Users of this standard are cautioned that compliance with Practice D does not astm d1633 itself ensure reliable results. Link to Active This link will always route to the current Active version of the standard. Compression tests provide information astn the compressive properties of plastics when employed under conditions approximating those under which the tests are made.

It is the responsibility of the use Astm d1633 values given in parentheses are mathematical conversions to SI units, and are provided for information only and are not astm d1633 standard. Related Suppliers Searching for related suppliers As a result, it has been customary to evaluate or specify compressive strength values as determined by Method A.